RDM EC9001f Guía de instalación

RDM Connect™ Installation GuideRevision B

6Inspect the Unit’s FeaturesDriver’s License or ID Card Entry Imaging SlotInsertion HopperExit PocketApplication Launch Button and Scanner Status LED3

7Internal ComponentsInside the Front Cover - Side ViewThe document feeder is on auto-feed models only.Application Launch Button and DiodesImage Sensor

8Inside the Front Cover - Back ViewDriver’s License or ID Card Entry Imaging SlotMetal Plate (aligns with hole in franker cartridge)Franker CartridgeC

9Inside the Front Cover and Endorsement Printer Cover - Top ViewMagnetic Stripe ReaderDriver’s License or ID Card Entry Imaging SlotImage Sensor and P

10Connection PortsUSB Hub PortsUSB Power On/Off SwitchK-SlotConnector DescriptionUSB Hub Ports Use this port to connect optional peripheral devices su

11Removing the CoversRDM Connect scanner has two covers that can be removed in order to clean the image sensor, replace cartridges, or clear paper jam

12Endorsement Printer CoverRemove the endorsement printer cover when you need to clear paper jams, to insert or replace the Endorser Inkjet Printer Ca

13Replacing the Franking Acknowledgement Printer Cartridge1. Remove the front cover.2. Lift the franker latch.3. Grasp the tab on the franker cartridg

14Replacing the Franking Acknowledgement Printer Cartridge123456

15Replacing the Endorser Inkjet Printer CartridgeWhen you place the new inkjet cartridge into the holder, make sure that you insert it at the angle de

RDM Connect™ Installation Guide Rev. BRevised: November 30, 2012© 2012 RDM CorporationThis manual, the RDM Connect™ Installation Guide, is intended fo

16Connecting the Power Cord1. Align the flat side of the power connector so that it is facing up.2. Insert the round end of the power cord into the po

17Operating the ScannerPreparing DocumentsTo reduce the possibility of errors and damage to the unit, you should: • Remove all folds and creases in th

18One document is scanned and processed.3. After the document is processed, click Scan again for each document remaining in the hopper.Swiping Magneti

19Imaging Identification CardsThe ID imager uses same track as the document scanner. The ID imager scans both the front and back of the identification

20Status SignalsThe scanner comes equipped with the default light and sound signals described below. Default Light SignalsThe unit’s status is shown t

212. The LED is Green (Flashing): The scanner is waiting for a document to be inserted for scanning.3. The LED is Green/Red (Flashing): The scanning o

22Maintaining the RDM Connect ScannerThe RDM Connect scanner performs best when all working surfaces are clean and free of foreign material.Cleaning t

23Cleaning the Image SensorOccasionally, it might be necessary to clean the image sensor.1. Remove the front cover and the endorsement printer cover.2

24TroubleshootingIn the course of everyday operations, you might encounter minor malfunctions in the RDM Connect scanner unit. Before calling for serv

25SpecificationsModel DetailsPhysical Dimensions Standard model: Width: 6.16″ Height: 6.88″ Length: 9.38″Document Size Minimum: 2.17″ W x 4.4″ L; Maxi

iContentsCompliance Statements ...

26Software and SupportSupported Operating Systems Windows XP, Vista (32/64-bit), Windows 7 (32/64-bit), Windows 8 (32/64-bit)Development Software Twai

27Warranty InformationLIMITED WARRANTY:RDM CONNECT™ is warranted against defects in materials and workmanship under normal use and service for a perio

28WARRANTY SPECIFICS:This warranty only covers failures due to defects in materials or workmanship, which occur during normal use.It does not cover th

ii

1Compliance StatementsFCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuan

2

3IntroductionThe RDM Connect™ scanner is a cost-effective, feature-rich, source item image and card processing solution. Using RDM’s industry leading

4RDM Connect Models and FeaturesThe RDM Connect scanner comes in several different models. Each model includes a certain set of features. Compare your

5Setting Up the RDM Connect ScannerTo set up the RDM Connect scanner, do the following:• Choose a Location• Unpack the Shipping Box• Inspect the Unit’