RDM EC9003f Guía de instalación

EC6000i®, EC7000i™, and EC7500i™ Series Installation Guide

8Setting Up the EC6000i, EC7000i, or EC7500iTo set up the EC6000i, the EC7000i, and the EC7500i, follow steps A – H.A. Choose a LocationLocate your sc

9C. Inspect the Unit’s FeaturesThe illustrations below show a basic scanner (Model A), and an EC7500i scanner with a Magnetic Stripe Reader (MSR) and

10Inside ComponentsCover LatchImage Frame in raised positionOutside Cover in raised positionImage SensorDocument Feed Plate comes out to reveal option

11Connection PortsRDM’s EC6000i, the EC7000i, and EC7500i can be installed in different configurations. These configurations are set and programmed by

12D. Insert the Franking Acknowledgement Printer Cartridge (Optional)The Franking Acknowledgement Printer Cartridge is an optional ink stamp, that mar

13II. Insert the Franking Acknowledgement Printer Cartridge into the Printer Assembly1. Insert the Franking Acknowledgment Printer Cartridge straigh

14E. Connect to a Telephone Line (EC6014 and EC7014)FOR TEL: If you have purchased the EC6000i or the EC7000i with the optional modem, follow these di

15F. Connect the Power Cord1. Insert the round end of the power cord into the power port on the back of the scanner.2. Align the flat side of the powe

16G. DriversThe drivers for your scanner are installed when you install your PC application. If it is a Web-based application, ActiveX may be installe

17Operating the ScannerPreparing ChecksTo reduce the possibility of errors and damage to the unit, you should: • Remove all folds and creases in the c

This manual, the EC6000i , EC7000i, and EC7500i Series Installation Guide, is intended for all units belonging to the EC6000i, EC7000i, and EC7500i fa

18Understanding Status SignalsThe scanner comes equipped with the default light and sound signals described below. Default Light SignalsThe unit’s sta

19Default Sound SignalsSeveral conditions are also signaled by a pattern of tones in addition to the LED display.A Typical Check Processing / LED Cycl

20Maintaining the EC6000i, EC7000i, or EC7500iThe EC6000i, EC7000i, or EC7500i performs best when all working surfaces are clean and free of foreign m

21Cleaning the ImagerOccasionally, it may be necessary to clean the image sensors and remove dust or debris from the interior of the EC6000i, the EC70

22TroubleshootingIn the course of everyday operations, you may encounter minor malfunctions in the EC6000i, the EC7000i, or the EC7500i unit. Before c

23 Check Feeder Does Not Function Properly Ensure that you are inserting the check properly: flush to the right side of the EC6000i, the EC7000i, or t

24Card Transactions Do Not Function Properly Test the Card Swipe Mechanism1. Ensure that you are swiping the card properly. The black magnetic stripe

25SpecificationsEC6000i, EC7000i, EC7500i SpecificationsUnit Size Without MSR 8.6″ long x 6.1″ wide x 4.4″ high21.9 cm long X 15.4 cm wide X 11.3 cm h

26EnvironmentalOperating Temperature 32 to 104 degrees F (0 to 40 degrees C).Operating Humidity 10 to 85% relative humidity (non-condensing).Document

27(Optional) Modem SpecificationsSupports V.34bis, V.34 V.F.C, V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Bell 212A and 103Error Correction V.42 LAP

1ContentsCompliance Statements ...2Introduction ...

28Warranty InformationLIMITED WARRANTY: The RDM EC6000i units are warranted against defects in materials and workmanship under normal use and service

29WARRANTY SPECIFICS: This warranty only covers failures due to defects in materials or workmanship, which occur during normal use. It does not cover

Copyright© RDM Corporation, 2009All rights reserved. No part of this document may be reproduced in any formwithout the written consent of RDM Corporat

2Compliance StatementsFCC Compliance StatementNOTE for EC6000i and EC7000i Series Scanners: This equipment has been tested and found to comply with th

3telephone line, contact the local telephone company. The REN for the EC6000i, EC7000i, or EC7500i Series Scanner is found on the underside of the uni

4Industry Canada Compliance StatementThis product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux s

5

6IntroductionThe EC6000i®, the EC7000i™, and the EC7500i™ Series Scanners are cost effective, feature rich, imaging solutions. Using RDM’s industry l

7Requirements• The EC6000i, the EC7000i, and the EC7500i units are for indoor use only. Keep the EC6000i, the EC7000i, and the EC7500i dry; avoid area